Bay & Bow Window Installation in Houston, TX | Custom Bay & Bow Windows
Houston Windows Replacement & Repair Pros offers its bay & bow window installation services in Houston, TX, around carpentry, since a projecting window is as much a small addition as it is a window. Our crews include framers and roofers alongside the installers, a combination assembled over 20 years because every bay needs its weight carried, its top roofed and its seat insulated by people who do that work daily.
Before any order, our estimators tape the unit's footprint on the floor and stake its outline in the yard, which shows owners exactly how far the window will reach into the room and toward the flower beds. Each projecting window also comes with written coverage on its structural support, separate from the glass, because a bay that drops even 1/4 inch at the nose starts to bind and leak.
Recent projects include restored bays on the early 1900s homes of Avondale and Westmoreland and new bows on family houses in Bear Creek, Champion Forest, Telfair and Silverlake, most of them replacing a flat picture window the owners had stopped noticing.
Why Choose Houston Windows Replacement & Repair Pros for Your Houston, TX Property
- 20 years replacing and repairing windows across Houston, TX and Harris County
- EPA Lead-Safe Certified Firm for homes built before 1978
- FGIA InstallationMasters certified installers on every crew
- General liability and workers' compensation coverage
- Window products with Texas Department of Insurance windstorm evaluations for storm-exposed properties
- Written, itemized estimates and a 10-year workmanship warranty
Get a FREE Quote
#1 Most Trusted Window Professionals in Houston
Bay & Bow Window Installation in Houston, TX
Residential and Commercial Bay Window Installation
Residential and commercial bay window installation creates a 3-sided projection, a fixed center window flanked by 2 angled units, in breakfast nooks, living rooms, restaurant booths and waiting areas.
Our residential window installation crew sets the flankers at 30 or 45 degrees, usually as casements or double-hung windows for ventilation, and chooses a projection between 12 and 24 inches to fit the room and the eave above.
The room gains daylight from 3 directions and a deep sill for seating or display, which is why a bay often becomes the spot everyone gravitates toward.
Residential and Commercial Bow Window Installation
Residential and commercial bow window installation produces a gentle curve from 4, 5 or 6 equal panels, a softer shape than a bay that spans wide walls in dens, sunrooms, cafes and hotel lobbies.
Each panel meets the next at roughly 10 to 15 degrees, and our estimators decide how many panels operate, since venting the 2 end units gives cross-breezes without interrupting the curve.
A bow projects less than a bay of the same width, which makes it the better choice where a sidewalk, driveway or property line sits close to the wall.
Whole-House and Whole-Building Bay Window Installation
Whole-house and whole-building bay window installation applies to properties with several projecting windows, such as Victorian-style homes, townhouse rows and apartment buildings with stacked bays on each floor.
Repetition demands consistency, and Houston Windows Replacement and Repair Pros builds every unit to the same angle, projection and roof detail, working from 1 set of shop drawings.
Matching bays read as original architecture from the street, and ordering them together lowers the cost per unit compared with adding them 1 at a time.
Single Bay and Bow Window Installation
Single bay and bow window installation turns 1 flat wall into the focal point of a room, most often at the front of the house or beside the kitchen table.
A projecting unit hangs its weight outside the wall, and our carpenters carry that load with steel cable supports anchored into the header above or with knee braces fastened below using Simpson Strong-Tie structural hardware.
Proper support keeps the seat level for decades, which protects the window seals and prevents the sagging outer corner that marks a poorly hung bay.
New-Construction Bay and Bow Window Installation
New-construction bay and bow window installation gives builders a choice that existing homes rarely have, extending the floor itself into the bay.
Our framing crew builds these walk-in bays on cantilevered joists or a small foundation bump-out, frames a hip or shed roof overhead and wraps the whole projection in the same weather barrier as the wall.
The finished bay adds real floor space to the room and insulates like the rest of the house, since it shares the wall's framing depth instead of hanging from it.
Replacement-Opening Bay and Bow Window Installation
Replacement-opening bay and bow window installation fits a factory-built projecting unit into the space where a flat picture window used to sit.
When the opening width stays the same, the existing header keeps doing its job, and our installers slide the unit in, tie its cables to the framing, insulate the seat board and cap the top with a small roof flashed into the siding or brick.
Houston Windows Replacement and Repair Pros pays particular attention to that head flashing, since a bay's roof catches more rain than any vertical window on the house during a Gulf storm.
Bay & Bow Window Installation Process in Houston, TX
Step 1: Layout and Structural Check
Our Houston Windows Replacement & Repair Pros estimator outlines the projection indoors and out, then inspects the header and wall framing. Eave height decides whether the unit needs its own roof.
Step 2: Unit Order
The factory builds the bay or bow with head and seat boards attached. Angle, panel count, operating units and interior wood species go on the order.
Step 3: Opening Preparation
Our carpenters remove the old window, adjust the framing and install support brackets or cable anchors. Sill flashing goes down before the unit arrives.
Step 4: Setting and Supporting
4 installers lift the unit in and level the seat. Cables or braces get tensioned until the outer edge holds true under load.
Step 5: Roofing, Insulation and Trim
A flashed roof or soffit closes the top, and foam insulates the seat and head. Interior casing and exterior skirt trim finish the job.
How Much Does Bay & Bow Window Installation Cost in Houston, TX?
Whether a window already occupies the spot is the first cost question. This Old House puts replacing an existing bow at $2,000 to $4,500, while installing one where no window existed before runs $3,000 to $10,000 or more.
Bays average $3,612 and bows $3,900, according to This Old House. A simple box bay is the cheapest type to install, and a customized bow in new construction reaches as much as $15,000. Frame material and the number of operating panels move the price within those ranges, since bow windows with more operable sections cost more.
Cost item | Typical figure |
|---|---|
Bay window, installed | $3,612 average, $1,038 to $7,911 |
Bow window, installed | $3,900 average, $1,500 to $15,000 |
Bay window installation, overall range | $950 to $7,500, with many near $2,500 |
Bow window replacement | $2,000 to $4,500 |
New bow where no window existed | $3,000 to $10,000 or more |
Fiberglass bow window | $1,400 to $3,800 |
Composite bow window | $1,400 to $4,600 |
Houston Windows Replacement and Repair Pros prices every projecting window after the layout and structural check, because the opening width, support method and roof tie-in are different on each Houston home.
Why We Are the Top Bay & Bow Window Installation Contractors in Houston, TX & Surrounding Areas
Seats Built to Sit On
Our Houston Windows Replacement & Repair Pros carpenters reinforce every seat board for real weight. Reading nooks and plant shelves hold up to daily use.
Roofs That Match the House
Shingles, metal or copper on the bay roof get matched to the main roof. The addition looks planned from the start.
Insulated Top and Bottom
Foam fills the head and seat cavities on every unit. Bays stop being the hot or cold spot of the room.
Brick and Siding Repaired
Wider openings disturb the wall around them. Our masons and siders patch brick, stucco or lap siding to blend in.
FAQs About Bay & Bow Window Installation in Houston, TX
Does Houston Windows Replacement and Repair Pros build the roof over a bay window?
Yes. Our roofers frame, flash and shingle a small roof over any bay that sits below the eave, matching your existing roofing so the Houston, TX home looks like it always had one.
Will Houston Windows Replacement and Repair Pros replace a flat window with a bay or bow?
Yes, and it's our most common project. A unit matching the old opening's width usually needs no new header, which keeps the work to 1 or 2 days at most Houston, TX homes.
Does Houston Windows Replacement and Repair Pros add window seats and storage to bay windows?
Yes, we do. Our carpenters build cushioned bench seats, hinged storage lids and bookshelf sides to order. Houston, TX customers choose the wood species and finish during the same visit as the window selection.
How much wall space does a bay or bow window need?
This Old House advises at least 40 inches of wall for a bay and 80 inches for a bow. Our estimators measure your wall and the clearance outside before recommending either one.
Should I choose a bay or a bow window?
Pick a bay for a deeper seat and a sharper, angled look, and a bow for a wide wall and a softer curve. Bows cost more for the same width because they hold more panels.
Do bay windows need HOA or city approval in Houston, TX?
Many HOAs review any change to a home's front elevation, and structural changes typically need a city permit. Our office prepares drawings for both and submits the applications on your behalf.
See a Bay or Bow Outlined at Your Houston Home
Call Houston Windows Replacement and Repair Pros for a layout visit. Our estimators mark the projection, check the framing and price your bay or bow window in writing.